Jump to content
tyga

Wanted - Action Screws For Anschutz Match 54

Recommended Posts

I have just bought a new stock (thumbwhole style) for my Match 54, and the action screws are far too long - currently 70mm and 42mm - they need to be more like 50mm and 27mm.

 

They seem to be an unusual thread (possibley 0.75 Metrisch 60degrees from thread guages??) and i don't have a die to modify the screws, so anyone have any spares lying around, or know where i could get some?

 

Thanks

 

Jim

Share this post


Link to post
Share on other sites

Hi Jim,

 

If you have the action screws and they are too long, some time ago, I bought a die and cut down / increased the thread length of similarly long screws.

 

They are mild steel screws and with a bit of lubricant, they cut OK.

 

I stand to be corrected, but I believe the thread die you require is 6mm metric FINE.

 

I bought mine from an engineering supplies company, 'off the shelf' without a problem : PILLAR Engineering in Portsmouth, Hants. I think?

 

If you want to persue this line, come back to me and I will dig my die out and check it's full spec.

 

Best of luck

 

Rob

Share this post


Link to post
Share on other sites

The Thread size you are looking for is 6mm x 0.75 pitch I doubt you will be able to get these off the shelf as they are not a common size in this country. however a gun dealer may have some lying about. The ones shown on Edinkille's website are not the right thread for bedding bolts.

 

If you accurately measure what you want from the bottom of the cap head to the end of the thread I may be able to make you some up.

 

Regards

 

Dave Clark

Share this post


Link to post
Share on other sites
The Thread size you are looking for is 6mm x 0.75 pitch I doubt you will be able to get these off the shelf as they are not a common size in this country. however a gun dealer may have some lying about. The ones shown on Edinkille's website are not the right thread for bedding bolts.

 

If you accurately measure what you want from the bottom of the cap head to the end of the thread I may be able to make you some up.

 

Regards

 

Dave Clark

 

Hi Dave,

 

The screws i need are as follows;

 

Screw 1 - 21.5mm total shaft length, 11mm thread length

Screw 2 - 47mm total shaft length, 13mm thread length

 

i would be very greatfull if you could make me these screws. How much would you charge?

 

Kind Regards

 

Jim Starley

Share this post


Link to post
Share on other sites
Hi Dave,

 

The screws i need are as follows;

 

Screw 1 - 21.5mm total shaft length, 11mm thread length

Screw 2 - 47mm total shaft length, 13mm thread length

 

i would be very greatfull if you could make me these screws. How much would you charge?

 

Kind Regards

 

Jim Starley

 

 

Hi Jim

 

I have sent you a p m

 

Dave

Share this post


Link to post
Share on other sites
Hi Dave,

 

The screws i need are as follows;

 

Screw 1 - 21.5mm total shaft length, 11mm thread length

Screw 2 - 47mm total shaft length, 13mm thread length

 

i would be very greatfull if you could make me these screws. How much would you charge?

 

Kind Regards

 

Jim Starley

 

 

Hi Jim

 

I have sent you a p m

 

Dave

 

Replied to PM

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×